GCSE Combined Science Physics 6: Potential Difference and Resistance

A Q A C O M B I N E D S C I E N C E · P H Y S I C S

Potential Difference and Resistance

Topic 2 Electricity · Lesson 6

1 / 25
next
Slide 1: Slide
New lesson editorPhysicsUpper Secondary (Key Stage 4)GCSE

This lesson contains 25 slides, with interactive quizzes and text slides.

Report this lesson

Introduction

Students learn how to measure potential difference with a voltmeter, use V = I R to link potential difference, current and resistance, and follow the required practical on how the length of a wire affects its resistance. Higher slides rearrange the equation and use the straight-line graph to predict resistance. Written for AQA GCSE Combined Science Trilogy (6.2.1.3), with a spec check for Edexcel, OCR Gateway and CCEA Double Award. This lesson was created with AI assistance.

Items in this lesson

A Q A C O M B I N E D S C I E N C E · P H Y S I C S

Potential Difference and Resistance

Topic 2 Electricity · Lesson 6

Physics Lesson 6 of the GCSE Combined Science series. Written for AQA Combined Science Trilogy 8464, section 6.2.1.3 (Current, resistance and potential difference), including the required practical on resistance (the effect of the length of a wire), Physics Paper 1.

Structure: 01 Hook, 02 Learn, 03 Check (including the Professor), 04 Go Higher (pink HIGHER badge), 05 Apply and Review. Foundation groups can stop before section 04.

The required practical also covers combinations of resistors in series and parallel - see Physics 7. V = I R must be recalled.

0 1 / H O O K

Which change would make a bulb in a simple circuit glow brighter?

1

Add more cells

2

Use a longer wire

3

Add another bulb in series

4

Use a thinner wire

P H Y S I C S

Take a vote and use the spinner to hear a few reasons.

Adding more cells increases the potential difference - a bigger "push" - so more current flows and the bulb glows brighter. A longer or thinner wire, or another bulb in series, adds resistance, so the current falls and the bulb gets dimmer. The next slide reveals it.

0 1 / H O O K

More cells - a bigger push!

More cells give a bigger potential difference, so more current flows.

Anything that resists the current makes it smaller.

Today: potential difference, resistance, and a required practical with a wire.

P H Y S I C S

Potential difference, current and resistance are linked by V = I R - the key equation for the whole electricity topic.

T O D A Y ' S G O A L S

By the end of the lesson

Foundation

  • I can measure potential difference with a voltmeter.

  • I can use V = I R.

  • I can describe the required practical on the resistance of a wire.

Higher

  • I can rearrange V = I R.

  • I can use a graph to predict resistance.

P H Y S I C S

Share the goals. Foundation goals are for everyone; the Higher goals are covered in section 04.

0 2 / L E A R N

Potential difference

Potential difference (p.d.) is the "push" that drives the current. It is often called voltage.

It is measured in volts (V) with a voltmeter.

A voltmeter is connected in parallel - across the component.

P H Y S I C S

AQA 6.2.1.3. An ammeter goes IN the loop (series); a voltmeter goes ACROSS the component (parallel). The drag-and-drop later in the lesson practises this.

0 3 / C H E C K

How is a voltmeter connected to measure the p.d. across a lamp?

A

In parallel, across it

B

In series with it

C

Anywhere in the loop

D

In place of the cell

Answer: in parallel - its two leads connect either side of the lamp. An ammeter is the one that goes in series. Image credit: Thorium / Unsplash

0 2 / L E A R N

V = I R

Resistance is how much a component opposes the current. It is measured in ohms (Ω).

potential difference = current × resistance

Example: 0.5 A through a 12 Ω resistor.

V = 0.5 × 12 = 6 V

P H Y S I C S

AQA 6.2.1.3: "The current through a component depends on both the resistance of the component and the potential difference across the component. The greater the resistance of the component the smaller the current for a given potential difference across the component." V = I R must be recalled.

0 3 / C H E C K

A current of 2 A flows through a 6 Ω resistor. What is the p.d. across it?

A

3 V

B

8 V

C

12 V

D

0.33 V

Answer: 12 V. V = I R = 2 × 6 = 12 V. 3 V divides 6 by 2; 8 V adds.

0 2 / L E A R N

Required practical: a wire

1 Clip the wire at a measured length.

2 Read the ammeter (I) and the voltmeter (V).

3 Calculate R = V ÷ I.

4 Move the clip and repeat for other lengths.

Keep the current small, so the wire does not heat up.

P H Y S I C S

AQA Required Practical (resistance): "Use circuit diagrams to set up and check appropriate circuits to investigate the factors affecting the resistance of electrical circuits. This should include the length of a wire at constant temperature and combinations of resistors in series and parallel."

Independent variable: length. Dependent variable: resistance (from V and I). Control variables: type and thickness of wire, temperature. Hazard: the wire can get hot - switch off between readings.

0 2 / L E A R N

The results

The graph is a straight line through the origin.

So resistance is directly proportional to length.

Double the length → double the resistance.

P H Y S I C S

Real results often do not quite go through the origin, because the crocodile clips and connections add a little resistance. That is a systematic error - a good discussion point.

0 3 / C H E C K

In the wire practical, what is the independent variable?

A

The current

B

The length of the wire

C

The potential difference

D

The resistance

Answer: the length of the wire - it is the variable you change on purpose. Resistance is the dependent variable, worked out from the current and the potential difference.


Drag each fact to the right meter

AMMETER

VOLTMETER

Connected in parallel

Measures current

Reads in volts (V)

Reads in amps (A)

Measures potential difference

Connected in series

P H Y S I C S

Ammeter: measures current; reads in amps (A); connected in series. Voltmeter: connected in parallel; reads in volts (V); measures potential difference.

T H E A N S W E R S E X P L A I N E D

How did we get those?

Voltmeter: connected in parallel, across the lamp. (The ammeter goes in series.)

p.d.: V = I R = 2 × 6 = 12 V.

Independent variable: the one you change on purpose - the length of the wire.

P H Y S I C S

Go through all three after the votes.

0 3 / C H E C K

"A LONGER wire has LESS resistance - the current has more room to move!" Is the Professor right? Explain.

T H E P R O F E S S O R S A Y S . . .

P H Y S I C S

The Professor's misconception, as an open question - students type their answers. His skeleton is holding up a ruler.

He is wrong. The practical shows resistance is directly proportional to length: a longer wire has MORE resistance. Doubling the length doubles the resistance. The charges have further to travel through the metal, so there is more opposition to the current.

Look for: "longer = more resistance", "directly proportional", "double length, double resistance", evidence from the graph.

T H E A N S W E R E X P L A I N E D

Sorry, Professor!

A longer wire has more resistance, not less.

The results graph is a straight line through the origin: resistance is directly proportional to length.

Double the length → double the resistance. The charges have further to travel through the wire.

P H Y S I C S

Go through this after students have typed their answers. Point back to the graph - the evidence settles it.

Potential difference and resistance recap

Potential difference is measured in volts with a voltmeter, connected in parallel. Resistance is measured in ohms. Potential difference = current × resistance. In the practical, the resistance of a wire is directly proportional to its length - a longer wire has more resistance.

volts
voltmeter
parallel
ohms
resistance
proportional
longer
series
amps
shorter

P H Y S I C S

A recap of the Foundation section. "Shorter" tests the Professor's misconception.

S P E C C H E C K

Your exam spec

V = I R and the resistance practical are in every specification.

AQA Combined Science Trilogy (8464) - 6.2.1.3, with the required practical on resistance, Physics Paper 1.

Edexcel Combined Science (1SC0) - Topic 10 Electricity and circuits: V = I × R, with core practicals on circuits.

OCR Gateway Combined Science (J250) - Electricity: resistance, with a practical activity (PAG).

CCEA Double Award Science (NI) - Physics: resistance and Ohm's law.

P H Y S I C S

A variant slide for classes on other specifications. Some boards call V = I R "Ohm's law" and expect the name.

Delete this slide if your class only sits AQA.

0 4 / G O H I G H E R

Rearranging and predicting

I = V ÷ R · R = V ÷ I

Worked example: 12 V across a resistor gives a current of 0.4 A. R = 12 ÷ 0.4 = 30 Ω.

Using proportion: resistance is directly proportional to length. A 40 cm wire is 1.6 Ω, so a 60 cm wire (1.5 times as long) is 1.6 × 1.5 = 2.4 Ω.

P H Y S I C S

HIGHER

Higher slide. Dividing by a decimal is where most errors happen - estimate first (12 ÷ 0.4 should be bigger than 12).

0 4 / G O H I G H E R

A p.d. of 6 V is across a 30 Ω resistor. What is the current?

HIGHER

A

0.2 A

B

5 A

C

36 A

D

180 A

Answer: 0.2 A. I = V ÷ R = 6 ÷ 30 = 0.2 A. 5 A divides the wrong way round; 180 A multiplies.

0 4 / G O H I G H E R

A 50 cm wire has a resistance of 2.0 Ω. What is a 75 cm wire of the same type?

HIGHER

A

1.5 Ω

B

2.5 Ω

C

3.0 Ω

D

3.75 Ω

Answer: 3.0 Ω. 75 cm is 1.5 times 50 cm, so the resistance is 1.5 × 2.0 = 3.0 Ω. 2.5 Ω adds 0.5 instead of multiplying.

T H E A N S W E R S E X P L A I N E D

How did we get those?

Current: I = V ÷ R = 6 ÷ 30 = 0.2 A. A big resistance gives a small current.

Wire: 75 ÷ 50 = 1.5 times as long, so 1.5 × 2.0 = 3.0 Ω. Directly proportional means you multiply, not add.

P H Y S I C S

HIGHER

Talk through both Higher answers.

0 5 / A P P L Y & R E V I E W

Exam practice

Question

A current of 0.4 A flows through a 15 Ω resistor. Calculate the potential difference across it. [2 marks]

Working space

Model answer

Key takeaway

Potential difference = current × resistance.

P H Y S I C S

FOUNDATION

Foundation exam question. Award both marks for the correct answer with no working.

0 5 / A P P L Y & R E V I E W

Exam practice

Question

Describe how to use this circuit to find how the resistance of a wire depends on its length. [4 marks]

Working space

Model answer

Key takeaway

Change, measure, calculate, repeat.

P H Y S I C S

HIGHER

Higher exam question. Credit "keep the current low / switch off between readings so the wire does not heat up" as an alternative fourth mark.

These are model points in the style of an AQA mark scheme, not an official mark scheme.

0 5 / A P P L Y & R E V I E W

Exit ticket: double the length of a wire - what happens to its resistance? How do you know?

P H Y S I C S

Exit ticket. Good answers: the resistance doubles - the graph of resistance against length is a straight line through the origin, so resistance is directly proportional to length.

Great work, scientists!

Next physics lesson - Physics 7, Series and parallel circuits.