GCSE Combined Science Physics 3: Specific Heat Capacity

A Q A C O M B I N E D S C I E N C E · P H Y S I C S

Specific Heat Capacity

Topic 1 Energy · Lesson 3

1 / 24
next
Slide 1: Slide
New lesson editorPhysicsUpper Secondary (Key Stage 4)GCSE

This lesson contains 24 slides, with interactive quizzes and text slides.

Report this lesson

Introduction

Students learn what specific heat capacity means, use ΔE = m c Δθ to calculate the energy needed to change the temperature of a material, and carry out the specific heat capacity required practical with a metal block, heater and joulemeter. Foundation slides come first, followed by Higher slides on rearranging the equation and evaluating the practical. Written for AQA GCSE Combined Science Trilogy (6.1.1.3 and Required Practical 14), with a spec check for Edexcel, OCR Gateway and CCEA Double Award. This lesson was created with AI assistance.

Items in this lesson

A Q A C O M B I N E D S C I E N C E · P H Y S I C S

Specific Heat Capacity

Topic 1 Energy · Lesson 3

Physics Lesson 3 of the GCSE Combined Science series. Written for AQA Combined Science Trilogy 8464, section 6.1.1.3 (Energy changes in systems) and Required Practical 14 (specific heat capacity), Physics Paper 1.

Structure: 01 Hook, 02 Learn, 03 Check (including the Professor), 04 Go Higher (pink HIGHER badge), 05 Apply and Review. Foundation groups can stop before section 04.

Students need calculators.

0 1 / H O O K

On a sunny morning at the beach, which warms up faster - the sand or the sea?

1

The sand

2

The sea

3

Both the same

4

Not sure

P H Y S I C S

Take a vote and use the spinner to hear a few reasons - many students will have felt hot sand and cold sea.

The sand warms up much faster. Water needs far more energy to raise its temperature than sand does - it has a high specific heat capacity. The next slide reveals this.

0 1 / H O O K

The sand - easily!

The Sun gives the sand and the sea energy at the same rate.

But water needs much more energy to warm up by each degree than sand does.

Today you will learn why - and calculate exactly how much energy it takes.

P H Y S I C S

Water's specific heat capacity is about 4200 J/kg °C; dry sand's is roughly 800 J/kg °C - about five times less (a typical value - figures vary with the sand).

T O D A Y ' S G O A L S

By the end of the lesson

Foundation

  • I can explain what specific heat capacity means.

  • I can calculate energy using ΔE = m c Δθ.

  • I can describe the specific heat capacity required practical.

Higher

  • I can rearrange the equation and evaluate the practical.

P H Y S I C S

Share the goals. Foundation goals are for everyone; the Higher goal is covered in section 04.

0 2 / L E A R N

What is specific heat capacity?

When you heat something, energy goes into its thermal store and its temperature rises.

The specific heat capacity of a material is the amount of energy needed to raise the temperature of 1 kg of it by 1 °C.

  • Water: about 4200 J to warm 1 kg by 1 °C - a lot!

  • Aluminium: about 900 J

  • Copper: about 390 J

The higher the specific heat capacity, the more energy it takes to warm up - and the more energy it stores.

P H Y S I C S

AQA 6.1.1.3. Students must be able to define specific heat capacity. Values are typical data-book values; exam questions always give the value they want used.

0 3 / C H E C K

The same energy goes into 1 kg of each. Which has the biggest temperature rise?

A

Copper (390 J/kg °C)

B

Aluminium (900 J/kg °C)

C

Water (4200 J/kg °C)

D

They all heat up at the same rate

Answer: copper. It has the lowest specific heat capacity, so each joule raises its temperature the most. Water has the highest, so it warms up the least.

0 2 / L E A R N

The equation

ΔE = m c Δθ

ΔE = change in thermal energy (J) · m = mass (kg) · c = specific heat capacity (J/kg °C) · Δθ = temperature change (°C)

Δθ means the change in temperature: final temperature - start temperature.

Worked example: heat 2 kg of water from 20 °C to 30 °C. c = 4200 J/kg °C.

Δθ = 30 - 20 = 10 °C · ΔE = 2 × 4200 × 10 = 84 000 J

P H Y S I C S

AQA 6.1.1.3. This equation is given on the AQA Physics equation sheet - students need to select and apply it.

Common error: using the final temperature instead of the change. Always work out Δθ first.

0 3 / C H E C K

How much energy heats 1 kg of water from 20 °C to 30 °C? (c = 4200 J/kg °C)

A

4200 J

B

126 000 J

C

42 000 J

D

420 J

Answer: 42 000 J. Δθ = 30 - 20 = 10 °C. ΔE = 1 × 4200 × 10 = 42 000 J. 126 000 J uses the final temperature (30 °C) instead of the change; 4200 J forgets to multiply by Δθ; 420 J divides by 10.

T H E A N S W E R S E X P L A I N E D

How did we get those?

Copper: the lower the specific heat capacity, the less energy each degree needs. So with the same energy, copper (390) heats up the most and water (4200) the least.

Water: first find the change: Δθ = 30 - 20 = 10 °C.

ΔE = m × c × Δθ = 1 × 4200 × 10 = 42 000 J

Used 30 instead of 10? That's the final temperature, not the change - you'd get 126 000 J.

P H Y S I C S

Go through both answers after the votes.

R E Q U I R E D P R A C T I C A L 1 4

Measuring specific heat capacity

A heater warms a metal block. The joulemeter measures the energy put in.

The thermometer measures the temperature rise.

P H Y S I C S

AQA Required Practical 14. Some schools use a voltmeter, ammeter and stopwatch instead of a joulemeter (energy = power × time). The block has two holes - one for the heater, one for the thermometer. A drop of water in the thermometer hole improves contact.

R E Q U I R E D P R A C T I C A L 1 4

The method

  1. Measure the mass of the block with a balance.

  2. Wrap the block in insulation - this reduces energy lost to the surroundings.

  3. Put the heater and thermometer in the holes. Record the start temperature.

  4. Switch on. When the temperature has risen by about 10 °C, record the energy on the joulemeter and the final temperature.

  5. Calculate: c = ΔE ÷ (m × Δθ)

Safety: the heater and block get hot - don't touch them, and let them cool before packing away.

P H Y S I C S

The rearranged equation is given here so Foundation students can complete the calculation; Higher students rearrange it themselves in section 04.

0 3 / C H E C K

Why is the metal block wrapped in insulation?

A

To make the block heat up faster

B

To reduce energy lost to the surroundings

C

To protect the thermometer

D

To keep the mass the same

Answer: to reduce energy lost to the surroundings. Then more of the energy measured by the joulemeter actually goes into the block, so the result for c is more accurate.

0 3 / C H E C K

"My little flask and the big bath are both 40 °C, so they must store the same thermal energy!" Is the Professor right? Explain.

T H E P R O F E S S O R S A Y S . . .

P H Y S I C S

The Professor's misconception, as an open question - students type their answers. He is mixing up temperature and energy.

He is wrong. Temperature is not the same as thermal energy. The energy stored depends on the mass as well as the temperature (ΔE = m c Δθ). The bath has a mass of 150 kg against 0.5 kg - 300 times more - so warming it to 40 °C took far more energy, and it stores far more thermal energy.

Look for: "mass", "temperature is not energy", "more energy needed", "ΔE = m c Δθ".

T H E A N S W E R E X P L A I N E D

Sorry, Professor!

Temperature isn't the same as energy.

The energy depends on the mass too: ΔE = m c Δθ.

The bath (150 kg) has 300 times the mass of the flask (0.5 kg), so it took far more energy to warm up - and stores far more thermal energy.

P H Y S I C S

Go through this after students have typed their answers. A full bath of warm water can keep a room warm for hours; a small flask cools in minutes.

Specific heat capacity recap

Specific heat capacity is the energy needed to raise the temperature of 1 kg of a material by 1 °C. Water has a high specific heat capacity. In the equation ΔE = m c Δθ, Δθ is the change in temperature. In the practical, the joulemeter measures the energy, and insulation reduces energy lost to the surroundings.

1 kg
1 °C
high
change
joulemeter
insulation
low
final
thermometer

P H Y S I C S

A recap of the Foundation section. "Final" tests the most common calculation error.

S P E C C H E C K

Your exam spec

Specific heat capacity and its practical are in every specification.

AQA Combined Science Trilogy (8464) - 6.1.1.3 Energy changes in systems and Required Practical 14, Physics Paper 1. The equation is on the equation sheet.

Edexcel Combined Science (1SC0) - Topic 14 Particle model, including the core practical on specific heat capacity.

OCR Gateway Combined Science (J250) - Matter: specific heat capacity.

CCEA Double Award Science (NI) - Physics, heat and energy.

P H Y S I C S

A variant slide for classes on other specifications. The core content is shared, but topic names, the practical method and whether the equation is given can differ - check your specification and its equation sheet before teaching.

Delete this slide if your class only sits AQA.

0 4 / G O H I G H E R

Rearranging and evaluating

To find c: c = ΔE ÷ (m × Δθ) · To find Δθ: Δθ = ΔE ÷ (m × c)

Worked example: 9000 J warms a 0.5 kg block by 20 °C. c = 9000 ÷ (0.5 × 20) = 9000 ÷ 10 = 900 J/kg °C

Why do results come out too high? Some energy from the heater is lost to the surroundings, or heats the heater itself, instead of the block. So the joulemeter reading is bigger than the energy that went into the block - and the calculated c is too high.

P H Y S I C S

HIGHER

Higher slide. Teaches the rearrangements and the evaluation point needed for the next two questions.

0 4 / G O H I G H E R

21 000 J heats 1 kg of water (c = 4200 J/kg °C). How much does its temperature rise?

HIGHER

A

25 °C

B

5 °C

C

20 °C

D

0.2 °C

Answer: 5 °C. Δθ = ΔE ÷ (m × c) = 21 000 ÷ (1 × 4200) = 5 °C. 0.2 °C divides the wrong way round.

0 4 / G O H I G H E R

A student's value for c is higher than the true value. What is the most likely reason?

HIGHER

A

Too high, because energy was lost to the surroundings

B

Too low, because energy was lost to the surroundings

C

Too high, because the block was too heavy

D

Exactly right, because a joulemeter was used

Answer: too high, because energy was lost to the surroundings. The joulemeter counts all the energy supplied, but some never reached the block, so ΔE in the calculation is too big.

T H E A N S W E R S E X P L A I N E D

How did we get those?

Temperature rise: Δθ = ΔE ÷ (m × c) = 21 000 ÷ (1 × 4200) = 5 °C. Work out the bottom first: 1 × 4200 = 4200.

Evaluation: energy lost to the surroundings is still counted by the joulemeter. ΔE on top of the fraction is too big, so c comes out too high. More insulation makes the result more accurate.

P H Y S I C S

HIGHER

Talk through both Higher answers. The evaluation point is a favourite 2-mark exam question.

0 5 / A P P L Y & R E V I E W

Exam practice

Question

A kettle heats 0.5 kg of water from 20 °C to 100 °C. c = 4200 J/kg °C.

Calculate the energy transferred to the water. [3 marks]

Working space

Model answer

Key takeaway

Find the temperature CHANGE first, then use ΔE = m c Δθ.

P H Y S I C S

FOUNDATION

Foundation exam question. One mark for the temperature change, one for substitution, one for the answer with unit.

0 5 / A P P L Y & R E V I E W

Exam practice

Question

In the practical, 12 600 J heats a 1 kg aluminium block from 20 °C to 34 °C.

Calculate the specific heat capacity of aluminium. [3 marks]

Working space

Model answer

Key takeaway

Rearrange to c = ΔE ÷ (m × Δθ), and give the unit J/kg °C.

P H Y S I C S

HIGHER

Higher exam question - the numbers match the joulemeter reading in the practical diagram. One mark each for Δθ, the rearranged substitution, and the answer with unit.

These are model points in the style of an AQA mark scheme, not an official mark scheme.

0 5 / A P P L Y & R E V I E W

Exit ticket: why does the sea stay cool on a hot day when the sand gets hot?

P H Y S I C S

Exit ticket. Good answers: water has a much higher specific heat capacity than sand, so it needs much more energy to raise its temperature by each degree; with the same energy from the Sun, the sea's temperature rises far less.

Great work, scientists!

Next physics lesson - Physics 4, Energy resources.