GCSE Combined Science Physics 7: Series and Parallel Circuits

A Q A C O M B I N E D S C I E N C E · P H Y S I C S

Series and Parallel Circuits

Topic 2 Electricity · Lesson 7

1 / 26
volgende
Slide 1: Slide
newEditorPhysicsUpper Secondary (Key Stage 4)GCSE

In deze les zitten 26 slides, met interactieve quizzen en tekstslides.

Dit is niet oké

Introductie

Students learn the rules for current, potential difference and resistance in series and parallel circuits, add resistances in series, and see why homes are wired in parallel. Higher slides solve series circuit problems step by step and explain why adding a resistor in parallel lowers the total resistance. Written for AQA GCSE Combined Science Trilogy (6.2.2), with a spec check for Edexcel, OCR Gateway and CCEA Double Award. This lesson was created with AI assistance.

Onderdelen in deze les

A Q A C O M B I N E D S C I E N C E · P H Y S I C S

Series and Parallel Circuits

Topic 2 Electricity · Lesson 7

Physics Lesson 7 of the GCSE Combined Science series. Written for AQA Combined Science Trilogy 8464, section 6.2.2 (Series and parallel circuits), Physics Paper 1. The resistance required practical also covers combinations of resistors in series and parallel.

Structure: 01 Hook, 02 Learn, 03 Check (including the Professor), 04 Go Higher (pink HIGHER badge), 05 Apply and Review. Foundation groups can stop before section 04.

AQA Combined Science does not require the calculation of total resistance for resistors in parallel - only a qualitative explanation.

0 1 / H O O K

One bulb in an old string of fairy lights breaks, and they ALL go out. Why?

1

They are wired in series

2

The plug's fuse blew

3

The battery went flat at that moment

4

They are wired in parallel

P H Y S I C S

Take a vote and use the spinner to hear a few reasons.

Old fairy lights were wired in series - one single loop. A broken bulb breaks the loop, so no current flows anywhere. In parallel, each bulb has its own branch, so the others stay on. The next slide reveals it.

0 1 / H O O K

One loop - one break stops it all

In a series circuit, everything is in one loop. Break it anywhere and the current stops.

In a parallel circuit, each component has its own branch.

Today: the rules for current, p.d. and resistance in each.

P H Y S I C S

Many modern fairy lights use parallel wiring or shunts so one failed bulb does not put out the whole set.

T O D A Y ' S G O A L S

By the end of the lesson

Foundation

  • I can describe current, p.d. and resistance in a series circuit.

  • I can describe current and p.d. in a parallel circuit.

  • I can add resistances in series.

Higher

  • I can solve series circuit problems step by step.

  • I can explain why resistors in parallel lower the total resistance.

P H Y S I C S

Share the goals. Foundation goals are for everyone; the Higher goals are covered in section 04.

0 2 / L E A R N

Series circuits

Current: the same through every component.

Potential difference: shared between the components (2 V + 4 V = 6 V).

Total resistance: add them up.

R total = R₁ + R₂

P H Y S I C S

AQA 6.2.2: "For components connected in series: there is the same current through each component; the total potential difference of the power supply is shared between the components; the total resistance of two components is the sum of the resistance of each component."

0 3 / C H E C K

In a series circuit, the current is...

A

The same everywhere

B

Shared between bulbs

C

Biggest near the battery

D

Zero after each bulb

Answer: the same at every point. It is the potential difference that is shared between the components in series. Image credit: Joanna Kosinska / Unsplash

0 3 / C H E C K

A 4 Ω and a 6 Ω resistor are in series. What is the total resistance?

A

2 Ω

B

2.4 Ω

C

10 Ω

D

24 Ω

Answer: 10 Ω. In series, add them: 4 + 6 = 10 Ω. 24 Ω multiplies; 2.4 Ω is the parallel value, which is not needed for Combined Science.

0 2 / L E A R N

Parallel circuits

Potential difference: the same across each branch - the full 6 V.

Current: splits between the branches. The total is the sum (1 A + 2 A = 3 A).

Total resistance: less than the smallest resistor.

P H Y S I C S

AQA 6.2.2: "For components connected in parallel: the potential difference across each component is the same; the total current through the whole circuit is the sum of the currents through the separate components; the total resistance of two resistors is less than the resistance of the smallest individual resistor."

0 2 / L E A R N

Why homes are wired in parallel

  • Every appliance gets the full mains potential difference.

  • Each one can be switched on and off on its own.

  • If one appliance breaks, the others keep working.

In series, the p.d. would be shared - and one broken lamp would switch off the whole house.

P H Y S I C S

A good link to mains electricity, later in Topic 2.

0 3 / C H E C K

In a parallel circuit, the p.d. across each branch is...

A

The same as the battery's

B

Shared between branches

C

Zero

D

Double the battery's

Answer: the same as the battery's - each branch is connected straight across the battery. Sharing the p.d. happens in series. Image credit: Thorium / Unsplash

0 3 / C H E C K

Two parallel branches carry 0.3 A and 0.5 A. What current leaves the battery?

A

0.15 A

B

0.2 A

C

0.4 A

D

0.8 A

Answer: 0.8 A - the currents in the branches add up to the total: 0.3 + 0.5 = 0.8 A. 0.2 A subtracts; 0.4 A averages.

0 2 / L E A R N

Series or parallel?

Series: one loop. Current the same, p.d. shared, resistances add.

Parallel: branches. P.d. the same, current splits, total resistance falls.

Learn the table - it answers most circuit questions.

P H Y S I C S

A summary of both circuit types before the drag-and-drop.


Drag each rule to series or parallel

SERIES

PARALLEL

Current splits

P.d. is shared

Used to wire homes

Resistances add up

Same p.d. on each branch

Same current everywhere

P H Y S I C S

Series: p.d. is shared; resistances add up; same current everywhere. Parallel: current splits; used to wire homes; same p.d. on each branch.

T H E A N S W E R S E X P L A I N E D

How did we get those?

Series current: the same everywhere - one loop, nothing used up.

Series resistance: add them: 4 + 6 = 10 Ω.

Parallel p.d.: each branch gets the full battery p.d.

Parallel current: the branches add up: 0.3 + 0.5 = 0.8 A.

P H Y S I C S

Go through all four after the votes.

0 3 / C H E C K

"Adding more resistors ALWAYS adds more resistance - even if you put them in parallel!" Is the Professor right? Explain.

T H E P R O F E S S O R S A Y S . . .

P H Y S I C S

The Professor's misconception, as an open question - students type their answers. He is holding his syringe.

He is wrong. In series, adding a resistor does increase the total resistance. But in parallel, adding a resistor gives the charge another path, so MORE current flows for the same potential difference - the total resistance goes DOWN. In the example, 6 Ω and 3 Ω in parallel give 2 Ω, less than either.

Look for: "in parallel the total resistance goes down", "another path / branch for the current", "more current for the same p.d.", "less than the smallest resistor".

T H E A N S W E R E X P L A I N E D

Sorry, Professor!

In series, yes - adding a resistor increases the total.

In parallel, adding a resistor gives the charge another path. More current flows for the same p.d., so the total resistance goes down.

6 Ω and 3 Ω in parallel give just 2 Ω - less than either one.

P H Y S I C S

Go through this after students have typed their answers. Analogy - opening another checkout in a shop lets more people through, even though each checkout is no faster.

Series and parallel recap

In a series circuit the current is the same everywhere and the potential difference is shared. To find the total resistance in series, add the resistances. In a parallel circuit the potential difference across each branch is the same, and the branch currents add up to the total. Adding a resistor in parallel makes the total resistance smaller. Homes are wired in parallel.

current
shared
add
same
total
smaller
parallel
bigger
series
multiply

P H Y S I C S

A recap of the Foundation section. "Bigger" tests the Professor's misconception.

S P E C C H E C K

Your exam spec

Series and parallel circuits are in every specification.

AQA Combined Science Trilogy (8464) - 6.2.2 Series and parallel circuits, Physics Paper 1.

Edexcel Combined Science (1SC0) - Topic 10 Electricity and circuits: series and parallel circuits.

OCR Gateway Combined Science (J250) - Electricity: series and parallel circuits.

CCEA Double Award Science (NI) - Physics: series and parallel circuits.

P H Y S I C S

A variant slide for classes on other specifications. Some boards (and AQA separate Physics) expect the calculation for resistors in parallel; AQA Combined Science only asks for a qualitative explanation.

Delete this slide if your class only sits AQA.

0 4 / G O H I G H E R

Solving series circuits

Example: a 12 V battery with 2 Ω and 4 Ω in series.

1 Total resistance: 2 + 4 = 6 Ω

2 Current: I = V ÷ R = 12 ÷ 6 = 2 A (the same everywhere)

3 P.d. across each: 2 × 2 = 4 V and 2 × 4 = 8 V - check: 4 + 8 = 12 V

Why parallel lowers R: each new branch is another path, so more current flows from the same p.d.

P H Y S I C S

HIGHER

Higher slide. AQA 6.2.2: students should be able to solve problems for circuits which include resistors in series using the concept of equivalent resistance, and explain qualitatively why adding resistors in parallel decreases the total resistance.

0 4 / G O H I G H E R

A 12 V battery is connected to 2 Ω and 4 Ω in series. What is the current?

HIGHER

A

2 A

B

3 A

C

6 A

D

72 A

Answer: 2 A. Total resistance 2 + 4 = 6 Ω; I = V ÷ R = 12 ÷ 6 = 2 A. 6 A uses only the 2 Ω resistor; 3 A uses only the 4 Ω one.

0 4 / G O H I G H E R

Why does adding a resistor in parallel lower the total resistance?

HIGHER

A

It gives charge another path

B

The new resistor is smaller

C

The p.d. goes down

D

Less charge flows

Answer: the new branch is another path for the charge, so more current flows from the battery for the same potential difference - a lower total resistance. It works whatever the size of the new resistor.

T H E A N S W E R S E X P L A I N E D

How did we get those?

Current: total R = 2 + 4 = 6 Ω first. Then I = 12 ÷ 6 = 2 A. Using one resistor on its own is the most common mistake.

Parallel: another branch means another path. More current flows for the same p.d., so R = V ÷ I gets smaller.

P H Y S I C S

HIGHER

Talk through both Higher answers.

0 5 / A P P L Y & R E V I E W

Exam practice

Question

A 5 Ω and a 7 Ω resistor are connected in series. Give the total resistance, and compare the current through each resistor. [2 marks]

Working space

Model answer

Key takeaway

Series - add the resistances; same current.

P H Y S I C S

FOUNDATION

Foundation exam question.

0 5 / A P P L Y & R E V I E W

Exam practice

Question

A 9 V battery is connected to a 1 Ω and a 2 Ω resistor in series. Calculate the p.d. across the 2 Ω resistor. [3 marks]

Working space

Model answer

Key takeaway

Total R, then current, then each p.d.

P H Y S I C S

HIGHER

Higher exam question. Accept the ratio method: the 2 Ω resistor has two-thirds of the resistance, so it gets two-thirds of 9 V = 6 V.

These are model points in the style of an AQA mark scheme, not an official mark scheme.

0 5 / A P P L Y & R E V I E W

Exit ticket: give two differences between series and parallel circuits.

P H Y S I C S

Exit ticket. Good answers: in series the current is the same everywhere, in parallel it splits; in series the p.d. is shared, in parallel each branch gets the full p.d.; in series one break stops everything, in parallel the other branches keep working.

Great work, scientists!

Next physics lesson - Physics 8, I-V characteristics and mains electricity.