Concrete mix design.pptx

Concrete and Mix Design

Matthew Holmes

matthewholmes@belfastmet.ac.uk

1 / 49
volgende
Slide 1: Slide
newEditor

In deze les zitten 49 slides, met tekstslides.

Dit is niet oké

Onderdelen in deze les

Concrete and Mix Design

Matthew Holmes

matthewholmes@belfastmet.ac.uk

Learner Objectives

  • By the end of the lesson you will be able to:

  • correctly identify key components and describe concrete process

  • Identify various types of Portland cement

  • List the types of aggregates used in concrete

  • Discuss the role of water in concrete

  • Calculate & carry out concrete mix design

Introduction to concrete

  • Concrete is one of the most widely used construction materials, with a long history of use.

  • Concrete is strong and durable, long lasting and possesses plastic qualities for infinite possibilities.

  • It is a man-made composite with the major constituent of which is natural aggregate such as:

    • Gravel

    • Sand

    • Crushed rock

Introduction to concrete

  • The other principal ingredient is the binding medium which is used to bind the particles together to form a hard composite material.

  • The most commonly used binder is the product which is formed by a chemical reaction between cement and water.

  • This process is known as hydration.

Introduction to concrete

  • In its hardened state, concrete is a rock-like material with a high compressive strength.

  • Fresh concrete in its plastic state, may be easily moulded into virtually any shape.

  • 2,000 years of development

    • Fall of Roman Empire the knowledge was lost

    • Discovered in 1824 by Englishman Joseph Aspdin, who coined it Portland cement.

Introduction to concrete

Cement

  • The word cement is used to cover a wide variety of materials, that when mixed, can be formed into shapes, and then set to become solid.

  • Within civil engineering terms, this generally means “hydraulic cement”

  • A cement that sets due to a chemical reaction with water, called hydration

  • Note; that the water used must be of a potable standard. Water of questionable standard can be used if the 7-day & 28-day cube tests have strengths equal to 90% of those made with clean water.

Cement

  • There are many different types of cement which are used in construction. The most commonly used cement is Portland cement. However, they all share the same important property that is:

Chemical reaction

Hydration

Strong binding agent for aggregates

Cement

Cement paste

Mortar

Concrete

Fine agg

Coarse agg

Cement

Uses of cement

Manufacture

Manufacture

Manufacture

  • Limestone, shale, sand milled and blended to dry meal

  • Cyclones and kiln, 750 °C → 900 °C → 1450 °C

  • Powdered coal, petroleum coke, waste tyre chips…

  • 5% added gypsum (calcium sulfate) to prevent excessively rapid flash setting of the cement

  • Stored in silos or in bags of 25 kg

  • 8% CO2 emissions from cement industry

Strength classes of cement

Admixtures

  • Plasticisers: ↑ workability by dispersing the cement grains; or ↓ w/c ratio  ↑ strength 15%.

  • Accelerators: ↑ rate of reaction between cement and water  ↑ rate of set and development of strength. Advantageous in precasting, for early removal of the formwork, and in cold weather.

  • Retarders: ↓ the rate of set.

Aggregates

  • Purpose

  • To make a strong, durable and economic concrete.

  • Requirements

  • Appropriate materials, size, grading and shape.

Workability

  • Describes the ability of the concrete mix:

    • to be placed within the formwork, around any reinforcement

    • to be successfully compacted by hand or mechanical means to remove trapped air pockets

Workability

Testing concrete

  • When a concrete mix design is being developed a few laboratory tests should be carried out. This is to ensure the quality of the concrete is maintained.

  • There are three common tests:

  • Slump test

  • Compressive test

  • Tensile test

Slump test

  • The most common test for workability. The method is described below:

  1. A truncated cone 300mm high is placed on a flat surface.

  2. Concrete is placed and compacted through an opening at the top.

  3. The cone is lifted and the extent to which the concrete slumps down is measured

Compressive test

  • This test is intended to measure the quality of the concrete. It does not pretend to give an accurate simulation of loading in a structure. Basic steps are outlined below:

  1. Concrete is sampled from site and is placed in cube and cylinder moulds, which are typically removed after a day.

  2. Samples are sent to the lab for testing (after curing)

  3. Specimens are set up in machine and tested.

  4. Failure load and type of failure is recorded

Tensile test

  • It is difficult to carry out a true tensile test. This is because the grips crush the ends causing failure. This is an indirect method of testing the tensile strength. General steps are noted below:

  1. After curing the samples are placed so that the longitudinal axis is perpendicular to the applied load

  2. Two strips of plywood are placed between the specimen and the bearing blocks of the test machine

  3. Specimens are tested and results are recorded

Concrete mix design – UK method

Concrete mix design – UK method

Concrete mix design – UK method

20

28

5%

20

28

5%

8

1.64

8

1.64

13

20

13

33

Free water is simply the difference between the mass of a sample of wet-saturated aggregate and the mass of the same sample in the saturated-surface-dry condition (SSD).

Or in other words;

the amount of water NOT being absorbed by the aggregate.

The water that is FREE to react with the cement.

20

28

5%

8

1.64

8

1.64

13

20

13

33

0.63

0.63

10-30

10

10-30

10

205

205

0.63

325

325

325

Saturated surface dry aggregate neither absorbs water from or contributes water to the concrete mixture.

2.7

2410

2410

325

205

1880

60

2.7

2410

2410

325

205

1880

60

41

1880

0.41

771

1880

771

1,109

325

205

770

1,110

0.0083

2.70

1.70

6.39

9.21

Trial mix of approx. 20kg

Group work

Data set

Characteristic compressive strength,

  • 30 N/mm2 at 28 days (group 1)

    • 40 N/mm2 at 28 days (group 2)

    • 40 N/mm2 at 28 days (group 3)

5% defective rate (k = 1.64)

Portland cement class 42.5

Aggregate type: coarse - Crushed

Aggregate type: fine

  • Crushed (Group 1 and 2)

    • Uncrushed (Group 3)

Maximum free-water/cement ratio, not specified

Slump required

  • 10 – 30 mm (Group 3)

    • 10 – 30 mm (Group 2)

    • 30 – 60 mm (Group 1)

Maximum aggregate size – 10 mm

Minimum/Maximum cement content, not specified

Relative density of aggregate, assumed

Percentage passing 600 μm sieve, 90%

Trial mix volume of 0.0083m

Data set

Characteristic compressive strength,

  • 30 N/mm2 at 28 days (group 1)

    • 30 N/mm2 at 28 days (group 2)

    • 40 N/mm2 at 28 days (group 3)

    • 40 N/mm2 at 28 days (group 4)

5% defective rate (k = 1.64)

Portland cement class 42.5

Aggregate type: coarse - Crushed

Aggregate type: fine – Crushed

Maximum free-water/cement ratio, not specified

Slump required

  • 10 – 30 mm (Group 1, 2, 3 and 4)

Maximum aggregate size

  • 10 mm (Group 1 and 3)

    • 20 mm (Group 2 and 4)

Minimum/Maximum cement content, not specified

Relative density of aggregate, assumed

Percentage passing 600 μm sieve, 90%

Trial mix volume of 0.0083m

Topic review

What are the basic ingredients in concrete?

Cement, water, aggregates

How does concrete cure and harden?

Chemical reaction > plastic gel > rigid gel

Hardening: gradual gain in strength of the set cement paste

What ingredients normally make up Portland cement?

Lime, silica, iron, alumina

What are the commonly used admixtures?

Plasticisers, accelerators, retarders

What is meant by the term workability?

Ability to be placed within the formwork, around any reinforcement

Name two other types of Portland cement?

White/coloured, sulfate resisting, low heat, extra rapid, ultra rapid etc

Learner Objectives

  • By the end of the lesson you will be able to correctly identify key components and describe concrete process:

  • Identify various types of Portland cement

  • List the types of aggregates used in concrete

  • Discuss the role of water in concrete

  • Calculate & carry out concrete mix design

Questions