Wat is LessonUp
Zoeken
Kanalen
Inloggen
Registreren
‹
Terug naar zoeken
VMI Basic principles of Maxx machine
Welcome to the VMI Quiz
1 / 23
volgende
Slide 1:
Tekstslide
ISK
Beroepsopleiding
In deze les zitten
23 slides
, met
interactieve quizzen
,
tekstslides
en
1 video
.
Lesduur is:
15 min
Start les
Bewaar
Deel
Printen
Onderdelen in deze les
Welcome to the VMI Quiz
Slide 1 - Tekstslide
Slide 2 - Video
Question 1
The HMI generated the following message:
BT DRUM lost his Home position
Slide 3 - Tekstslide
How can we solve this problem?
A
Move it manual back to its home position
B
Change position in Parameter
C
Recalibrate the drum
D
Power on/off the machine
Slide 4 - Quizvraag
Question 2
You want to start production and you notice the robot teach pendant like in the picture on the left
Slide 5 - Tekstslide
What is not correct related to the teach pendant?
A
The screen is ON
B
The Teach pendant has to be outside the machine
C
The Teachscreen is not closed
D
Everything is correct
Slide 6 - Quizvraag
Question 3
The detection wheel is not functioning properly in means of sensor adjusment
Slide 7 - Tekstslide
What is the thickness of the plate to adjust the sensor properly?
A
10mm
B
1mm
C
0.1mm
D
0.4mm
Slide 8 - Quizvraag
The centering system is constantly centering without any movement of the material
Question 4
Slide 9 - Tekstslide
What is the reason of centering without movement of material?
A
It is a parameter setting
B
The lens is dirty
C
This is a normal behaviour
D
This is because the material is too wide
Slide 10 - Quizvraag
Question 5
The cutter needs to be adjusted
Slide 11 - Tekstslide
What is the correct distance between the tip of the knife and cutter bar?
A
0.1mm
B
0.2mm
C
0.5mm
D
0.8mm
Slide 12 - Quizvraag
Question 6
The cutter needs to be adjusted
Slide 13 - Tekstslide
What is the correct distance between back of the knife and cutter bar?
A
0.1mm
B
0.2mm
C
0.5mm
D
0.8mm
Slide 14 - Quizvraag
When you have to remove the breaker from applicator conveyor
Question 7
Slide 15 - Tekstslide
How do we remove breaker material from the apply conveyor ?
A
Jog reverse the material first till it passed by the LM wheel. And remove the material
B
Jog reverse the material to the cutter. And remove the material
C
Jog forward the material to the front. And remove the material
D
Just remove the material
Slide 16 - Quizvraag
During Tread apply there are some important points to notice
Question 8
Slide 17 - Tekstslide
What is going wrong in the GIF?
A
Lasers are not in the correct width
B
Sticker robot is not allowed to move
C
GTRU robot is not allowed to move
D
BT drum is not pushing against MDS rolls
Slide 18 - Quizvraag
Question 9
When the beadsetters are closed, there must be a certain distance between the arms
Slide 19 - Tekstslide
What has to be distance between the two beadset arms?
A
3MM
B
8MM
C
10MM
D
1MM
Slide 20 - Quizvraag
Teaching the robot
Question 10
Slide 21 - Tekstslide
What is a safe (recommended) speed to teach the robot?
A
35%
B
50%
C
75%
D
25%
Slide 22 - Quizvraag
You are done :)
Thank you for presence and time
Slide 23 - Tekstslide
Meer lessen zoals deze
Chapter 1: paragraph 3
Oktober 2021
- Les met
15 slides
Aardrijkskunde
Middelbare school
vwo
Leerjaar 1
§1.3 Global positioning 2
September 2022
- Les met
12 slides
Aardrijkskunde
Middelbare school
havo
Leerjaar 1
C1.3 Canada - Lesson 8: Quiz preperation
Oktober 2022
- Les met
14 slides
Aardrijkskunde
Middelbare school
vwo
Leerjaar 1
Lesson 9 – 1D
Juni 2023
- Les met
23 slides
Nask
MBO
Studiejaar 1
1TTO CH4 Overview Lesson 6
Maart 2024
- Les met
17 slides
Wiskunde
Middelbare school
vwo
Leerjaar 1
De geo Tehran: the location of tehran lesson 2
Oktober 2022
- Les met
11 slides
Aardrijkskunde
Middelbare school
vwo
Leerjaar 1
(Average) Speed & velocity
Augustus 2020
- Les met
47 slides
Natuurkunde
Middelbare school
havo, vwo
Leerjaar 2,3
Lesson 9 – 1E
Juni 2023
- Les met
20 slides
Nask
MBO
Studiejaar 1