Measuring SHC

25/11/25 Measuring SHC 6-marker

Starter:

  1. What is SHC? The amount of energy needed to raise the temp of 1 kg of the substance by 1 C.

  2. SHC of water is 4200 J/(kg x C). If 3 kg of water is heated by 4 C, how much energy is transferred? Energy = 4200 x 3 x 4 = 50 400 J

  3. State SI units of mass. kg

  4. What do we use to measure mass? top pan balance

1 / 18
volgende
Slide 1: Slide
newEditorPhysicsUpper Secondary (Key Stage 4)GCSE

In deze les zitten 18 slides, met interactieve quizzen en tekstslides.

time-iconLesduur is: 30 min
Dit is niet oké

Onderdelen in deze les

25/11/25 Measuring SHC 6-marker

Starter:

  1. What is SHC? The amount of energy needed to raise the temp of 1 kg of the substance by 1 C.

  2. SHC of water is 4200 J/(kg x C). If 3 kg of water is heated by 4 C, how much energy is transferred? Energy = 4200 x 3 x 4 = 50 400 J

  3. State SI units of mass. kg

  4. What do we use to measure mass? top pan balance

What is the Specific Heat Capacity (SHC)?

The Specific Heat Capacity is the amount of energy needed to raise the temperature of 1 kg of a substance by 1 °C.

Higher SHC means the substance heats up faster.

Lower SHC means the substance heats up slower.

temperature
1
1
faster
slower
at the same rate
100

What is the correct formula that allows to determine SHC?

A

Energy Transfer = Mass x SHC x Change in Temperature

B

Energy Transfer = Mass x SHC x Temperature

C

Energy Transfer = Weight x SHC x Change in Temperature

D

Energy Transfer = Mass x SHC x Time

What do you need to know to determine the SHC according to the formula?

Energy Transfer = Mass x SHC x Change in Temperature

How would you measure the mass of an aluminium block?

How would you measure the change in temperature of an aluminium block?

Now the trickiest bit...

How would you measure the energy transferred?

Arrange these key steps in the right order. Think about the practical that we've done.

1

Measure the temperature each minute for 10 minutes

2

Calculate Energy Transferred = Voltage x Current x Time

3

Calculate SHC by Energy Transferred = Mass x SHC x Change in Temperature

4

Use a large linear section to determine Change in Temperature and Time

5

Plot the graph of the Temperature over Time, draw a line of best fit

6

Measure the mass of an aluminium block using a top-pan balance

Are you happy to start answering a 6-marker about this practical??

When describing a method, you do not need to indicate the equipment you're using.

1

AGREE

2

DISAGREE

When describing a method, you need to provide all formulae you need to calculate what's needed

1

AGREE

2

DISAGREE

When drawing a diagram with the equipment, you need to label all pieces of equipment on this diagram

1

AGREE

2

DISAGREE

Voltmeter is connected in parallel to a heater

1

AGREE

2

DISAGREE

Ammeter is connected in parallel to a heater

1

AGREE

2

DISAGREE

What do readings from the voltmeter, ammeter and time allow you to calculate?

Why would you need a stopwatch in this practical?

A

To stop and watch

B

To measure temperature change

C

To measure time

D

To measure

In your books:

  1. Draw a labelled diagram showing how the apparatus used to determine the specific heat capacity of aluminium should be arranged.

  2. Describe how you could use the apparatus you drew in part (a) to determine the specific heat capacity of aluminium.

Mark your work!

1-2 marks: some steps identified, no links

3-4 marks: up to 70% of steps identified and linked together

5-6 marks: 80-100% steps identified and linked together


Green pen - add what you've missed.