FLT Presentation

1

Course Instructor


Lee Chisholm

Representing


LMC Training Services



Fork Lift Truck Operator Training

1 / 93
volgende
Slide 1: Slide
newEditor

In deze les zitten 93 slides, met tekstslides.

Dit is niet oké

Onderdelen in deze les

1

Course Instructor


Lee Chisholm

Representing


LMC Training Services



Fork Lift Truck Operator Training

2

Fire Alarm, Tests and Evacuation

Welfare Facilities

Phones

SAFETY AND WELFARE INFORMATION

Company Induction Video

For you, as operators, to be aware of the Rules & Regulations regarding the use of Lift Truck.


To be competent in the operation & good operating practice, of a Lift Truck, to nationally recognised standards.


3

Aims and Objectives

By the end of this course to achieve a Certificate of Competence you will have to:


  1. Pass an Associated knowledge Exam

  2. Complete a Pre-use check on equipment

  3. Pass a Basic skills Test

4

Aims and Objectives

5

Acts

&

Regulations

LAW

6


The Health and Safety at Work Act 1974 (HSW Act).


The Provision and Use of Work Equipment Regulations 1998 (PUWER) (ACOP).

The Lifting Operations and Lifting Equipment Regulations 1998 (LOLER) (ACOP).

The main legislation applying to the use of lift trucks are:

7

The Health and Safety

at Work Act

1974



H.A.S.W.A 1974

8

Section 2

2a To provide safe plant and safe systems of work.

2b The safety and absence of risks in connection with use,

handling, storage and transportation of articles and

substances.


2c Provide adequate information, instruction, training and supervision.

2d Maintain a safe place of work and access to, or egress from, the workplace.

2e Safe working environment.

Employer’s Duties to their Employee’s

9

Section 7

a Duty to take reasonable care of themselves and other

persons who may be affected by their acts or omissions.

b Duty to co-operate with the employer and other persons in ALL matters concerning Health and

Safety.


Section 8

Duty not to interfere with, or recklessly misuse, anything provided in the interests of

health, safety or welfare.

Employees Duties

10

An Approved Code of Practice set out by the HSE which

is advice to duty holders on

how to comply with legislation.


Approved Code of Practice (ACOP)


11

Provision and Use of Work Equipment Regulations 1998 (L22) (P.U.W.E.R)

A.C.O.P

12

Regulation 5

 

(1): Every employer shall ensure that work

equipment is maintained in an efficient state,

in efficient working order and in good repair.


(2): Every employer shall ensure where any

machinery has a maintenance log, the log

is kept up to date.



PUWER 1998

13

Regulation 9


9(1) Every employer shall ensure that all persons who

use work equipment have received adequate training for

purposes of health and safety, including training in the

methods which may be adopted when using the work

equipment, any risks which such use may entail and

precautions to be taken.


PUWER 1998

14

Regulation 26 Sec 2

 

Where there is a risk of anyone being carried by mobile work equipment being crushed by it’s rolling over, the employer shall ensure that it has suitable restraining system for them.


i.e. a seat belt.

 


PUWER 1998

15

Regulation 28

 

Every employer shall ensure that no employee is

carried on mobile work equipment, unless:-


a) It is suitable for carrying persons, and;


b) It incorporates features for reducing risks

to their safety, including risks from

wheels or tracks.


PUWER 1998

16


Lifting Operations and Lifting Equipment Regulations 1998 (L113)

(L.O.L.E.R)


A.C.O.P

17

Regulation 8 states:


“ Every employer shall ensure that every lifting operation, involving lifting equipment, is properly planned by a competent person, appropriately supervised and carried out in a safe manner.”

Lifting Operations and Lifting Equipment Regulations 1998

18

Lifting Operations and Lifting Equipment Regulations 1998

Regulation 9 (3)

Every Employer shall ensure that lifting equipment which is exposed to conditions causing deterioration which is liable to result in dangerous situations is thoroughly examined:

(i) in the case of lifting equipment for lifting persons or accessory for lifting at least every 6 months

(ii) in the case of lifting equipment at least every 12 months

19

Rider Operated Lift Trucks Operator Training. (L117)
(R.O.L.T.O.T)


A.C.O.P

20

Rider Operated Means:-


“any truck capable of carrying an

operator, including trucks controlled

from both seated and stand-on positions, which may be fixed or fold away”.


Approved Code of Practice (L117) “Rider Operated Lift Trucks Operator Training”

21

Operator training should always include three stages:

Stage 1: - Basic Training

Stage 2: - Specific Job Training

Stage 3: - Familiarisation Training


Basic Training & Specific Job Training

can be combined or integrated but should always be off the job.

Approved Code of Practice (L117) “Rider Operated Lift Trucks Operator Training”

FILMS

Reach

Combilift

Counterbalance

22

23

Fork Lift Truck Stability

24

Fork Lift Truck Stability

THE NATURAL AXES OF LIFT TRUCKS

The stability of a lift truck is designed to allow for uneven

ground. It is vital that the steering axle is pivoted at its centre.

This gives the lift truck the same stability characteristics of a

wheel barrow, a triangular area of great stability narrowing at

one end (C).

25

Fork Lift Truck Stability

Dot 1 shows the Centre of Gravity without a load

Dot 2 shows the Centre of Gravity with a load on

Dot 3 shows the Centre of Gravity with tilt applied

26

Fork Lift Truck Stability

The rated capacity of the equipment will be reduced the further the centre of gravity of the load is from the face of the forks.


27

Fork Lift Truck Stability

28

Fork Lift Truck Stability


The Fulcrum Point on the Lift Truck is the CENTRE of the front wheels. If the load exceeds that stated on the Lift Truck’s Capacity Plate the Truck will become unstable and could TIP FORWARDS

29

The weight of the the fork lift truck should never be increased in

an attempt to lift heavier loads

If you attempt to add weight to the back of the truck it will become unstable

Fork Lift Truck Stability

30

To comply with the manufacturers stated

lifting capacity the lift truck’s mast must be

vertical with the truck on level ground.


Rated Capacity Plates & Safe Working Loads

Before picking up a load check its weight, size,

load centre, the height which the load has to be placed and its condition and security.

Rated capacity plates should clearly indicate

the weight the lift truck can lift, to what load

centre and what height.

Never exceed the lift truck rated capacity.

31

Rated Capacity Plates & Safe Working Loads

The WEIGHT:


Exceed the weight the lift truck can safely lift and it will lose longitudinal stability(front to back) possibly causing it to tip forwards.

32

Rated Capacity Plates & Safe Working Loads

33

Rated Capacity Plates & Safe Working Loads

LOAD CENTRES

A Load Centre is the distance measured from the vertical face of the forks to the centre point of

gravity of the load.

The trucks maximum capacity will be reduced when the load

centre is increased.


34

Rated Capacity Plates & Safe Working Loads

The Load Centre:

Exceed the load centre to weight ratio and the lift truck will lose longitudinal stability possibly causing the lift truck to tip forward.

35

Rated Capacity Plates & Safe Working Loads

36

If you exceed the height to the weight shown on the lift truck’s Capacity Plate you will lose longitudinal stability, possibly causing the lift truck to tip

forward


THE HIGHER THE LOAD THE WORSE THE SITUATION

Rated Capacity Plates & Safe Working Loads

37


Rated Capacity Plates & Safe Working Loads

38

Rated Capacity Plates & Safe Working Loads

39

Rated Capacity Plates & Safe Working Loads

The Load below has a load centre of

600mm. How much weight can the lift truck

lift?

40

Rated Capacity Plates & Safe Working Loads

You have been tasked to pick up an uneven load.


The view is from the top.


From which direction are you going to pick it up:


A, B, C, D

41

Rated Capacity Plates & Safe Working Loads

42

Exceeding the trucks maximum SWL (To much weight).

Exceeding the load centre to weight ratio (undercutting,

having the weight too far forwards on forks).

Exceeding the height to weight ratio (travelling with a raised load).   

Sudden braking.

Misuse of forward tilt.

Travelling in the wrong direction on an incline, laden or unladen.

Live load.

Causes of Longitudinal Instability (forwards).

Fork Lift Truck Stability

43

Inclines:

When an unladen truck is being driven on a gradient,

to improve stability, traction and adhesion, the forks should face downhill.

Fork Lift Truck Stability

When laden the load must face up the incline.

When unladen the forks must

face down the incline.

44

Causes of Lateral Instability (sideways).

Tyres (incorrect tyre pressure, uneven wear on solid

tyres).

Turning at speed. (Turning sharply).

Turning on an incline.

Hitting an obstruction (ground conditions).

Excessive backward tilt at height.

Uneven load.

Live load.

Lifting on one fork.

Incorrect use of side shift.

Fork Lift Truck Stability

Forklift Safety




Safety Essentials

45

46

Operators Safety Code

47

Stopping approximately 150mm from the stack/load/rack will assist the operator with accuracy, reduce damage and discourage persons walking between the lift truck and stack/load/rack.

Operators Safety Code

48

WHY?

To prevent accidents by the habitual use of safe

working practices.

ACCIDENTS?

An unexplained or unexpected event, which could

produce: -

  • DAMAGE

  • INJURY

  • DEATH

Operators Safety Code

49

SAFETY?

Being free from hazard & risk.

Operators Safety Code

HAZARDS?

The conditions creating risk of accident.

Removing the hazard automatically removes the risk.

Where the hazard cannot be removed care and

necessary action must be taken at all times.

50

HOW IS SAFETY ENSURED?

By obeying the

OPERATOR,

MANUFACTURERS

and

COMPANY,

SAFETY CODES, PROCEDURES and POLICIES.

Operators Safety Code

51

Operators Safety Code


Operators are only to operate equipments for which they hold a valid certificate of competence…

52

Operators Safety Code

and…

Have written authorization from their employer.



Authorisation To Operate

Mr Well Trained

53

Operators Safety Code

If a fault is found, or occurs, on the fork truck stop immediately and seek assistance.

The operator is responsible for checking that the

lift truck is in good working order before using it.

The lift truck operator is responsible to ensure the

safety of pedestrians while operating a lift truck.


54

Operators Safety Code

Do not be distracted and there must be no

lapses in concentration or practical jokes when operating a FLT.

The operator must not allow anyone to travel on

the FLT or any part of the FLT unless the truck has

been designed for that purpose.


Do not allow anyone to stand or walk under raised forks.

55

Operators Safety Code

Operators are to keep all parts of the body within the confines of the equipment except: when they are stacking or de-stacking in an aisle, for alignment purposes, with the handbrake applied.

When leaving a FLT unattended ensure: -

Handbrake on

Forks on the ground

Key removed to stop unauthorised use

56

Operators Safety Code

Do not park an industrial lift truck near doorways,

switches or electricity boards, fire fighting

equipment, blind corners, on inclines, loading bays, wet or muddy areas, soft ground or, generally, anywhere in the way of others.

57

Operators Safety Code

Always travel at a speed consistent with the type of load and general working conditions.

Slow down at intersections and corners and do not overtake any other vehicle at these points.

58


Operators Safety Code

Changes in ground surfaces, such as wet/dry, icy or greasy, very smooth, loose surfaces, inclines, railway lines or gullies can cause instability, loss of adhesion or braking, damage or loss of load. Always drive across railway lines, drainage gullies etc slowly and, if possible, diagonally.

59

Operators Safety Code

Sound the horn (few sharp blasts) when

approaching intersections, corners or any blind spots and if possible drive wide to increase visibility.

When turning ensure there is enough room for the rear and front end swing.


Check before entering lifts or driving over dock levellers or bridge plates that they are safe, able to take the combined weight of the FLT and load

and that a suitable Risk Assessment has been carried out.

60

Operators Safety Code

When following another truck keep

a minimum of three truck lengths

from the truck in front.

x

x

Always look in the direction of travel, especially when reversing, have a clear view of the way ahead and be aware of overhead obstructions; be sure there is enough room for safe operations.

61

Operators Safety Code

Whist operating a lift truck, if you see some rubbish or dunnage, lying in a gangway, or

warehouse location, park the truck in a safe

place and remove the obstruction.

The safest procedure when preparing to move

off is select transmission, look around, hand brake off, then move.

62

Operators Safety Code

In normal circumstances, if the load on the forks

obscures your view you should travel in reverse,

looking in the direction of travel (except when

travelling up a hill then get someone to guide you).

When driving an unladen truck the forks should

be set as low as practicable and tilted back.

Do not drive or operate a lift truck across inclines

as this will reduce sideways stability and the lift

truck has a strong possibility of overturning.

63

Operators Safety Code

The load centre will be increased

when tilting a load forward at height.

Never use the full range of tilt at

height, laden or unladen.

Net weight = the weight of the load:

In winter months loads stacked outside may

be covered in ice and snow, the effect of this

will increase the weight of the load.

Gross weight = the weight of the

Load, the pallet and any packaging.

64

Operators Safety Code

When handling metal stillages the forks must be positioned as wide as possible to prevent the load slipping sideways.

Ensure the fork arms are set so that they are able

to take equal weight on each fork before entering

a palletised load.

65

Operators Safety Code

When parking a lift truck the tips should be touching the ground with the heels as low as possible.

Apply the parking brake and place into neutral

before using any hydraulic controls


  • To ensure the lift truck is stable during the operation

  • The operator will be able to concentrate on the stacking/destacking

  • Some engined trucks require the engine to be revved to assist with lifting

66

Don’t use any Defective or Damaged Pallets/Equipment

67

Operators Safety Code

When picking up a load, ensure it is fully heeled

to keep the load centre as short as possible,

to maintain truck stability, to keep the truck and its

load as short as possible for confined areas and

to maintain load stability against the fork arms

and carriage, unless undercutting the load is

required.

Undercutting is used when the forks are

longer than the pallet and the pallet is

adjacent to a wall, or another pallet, or the

pallet cannot be heeled up immediately.

Be aware when undercutting of the

weight/load centre ratio.


68

Operators Safety Code

Apply sufficient back tilt to cater for the type of

load and ground conditions when transporting

a palletised load. Never use the full range of forward tilt, with the forks raised, laden or unladen.

The meaning of “free lift “in connection with lift trucks is the distance the forks can be raised before the mast begins to extend.

69

If a side shift is fitted to a lift truck it may reduce the lift trucks

lifting capacity, it may reduce visibility, stability and it will

require to be repositioned (centrally) after use.

Rated Capacity Plates & Safe Working Loads

70

DO NOT

Try and jump clear of a FLT that is tipping

Survive a Tip over

Operators are only to fit and use attachments for which they have received training.

71

Operators Safety Code

72

Things to be aware of when fitting attachments!


The rated capacity of the equipment will be reduced.

Attachments must be suitable for the truck.

Attachments are secure and all hoses if fitted are connected correctly and in good order.

Attachments are in good order.


Fitting Attachments

73

Before loading or unloading a flat bed or curtainsider lorry ensure: -

  • The vehicle is on flat firm ground

  • The bed of the lorry is in good conditions

  • The driver has applied the parking brake and chocked the wheels (if applicable)

  • The engine is switched off


  • He/she is aware of your intentions

Vehicle Loading and Unloading

  • The side curtain is out the way

74

When loading a lorry it is important that loaded

pallets are placed tight to one another and against

the headboard, to reduce load movement

in transit, especially when the lorry is braking and

to ensure the lorry will take a full load;

Vehicle Loading and Unloading

or where the driver tells you where they want it.

75

The use of trucks to support working platforms is in direct contravention of the Health & Safety at Work Act, unless certain precautions are taken.


If a FLT is to be used in this manner then an approved safety cage should be used.

The Use of Fork Trucks as a Work Platform

Before using a safety cage (manned platform) ensure That:


It is serviceable and complies with HSE requirements.

Suited to the lift truck it is to be used with.

Check the Capacity Plate of the cage to make sure the truck has correct lifting capability.

It is secured to the lift truck using the correct method (Locking pins only).

There is a safe method of use agreed before using the safety cage.

Only authorised persons are lifted in the safety

cage.

Hard hats are worn where required.


76

Example Hydraulic System

77

78

Visual Checks: To ensure components are not damaged.

Operational checks: To ensure all mechanical, hydraulic and electrical parts are working correctly.

Log Sheet/Form: Used daily by the operator to note any

faults both visual & operational. This

form should be signed by a supervisor or manager daily bringing to their attention any faults with the truck.


The completed form should be available for any other

operator who may be required to operate the truck within

the working day.

Daily / Pre-Shift Checks

79

REMEMBER IF A FAULT OCCURS AT ANY TIME THEY

MUST BE REPORTED IMMEDIATELY.

Daily / Pre-Shift Checks

Electric

Diesel/Petrol

LPG

80

Mode of Power

81

Check that there are no sources of ignition,

naked flames, cigarettes etc.

Electrolyte: Mixture of distilled water and sulphuric

acid; when charging gives off highly explosive and toxic gases.

Always disconnect the battery from the charger before checking and topping up.

Do not wear jewellery, watches etc. When checking the

battery.

PPE: Gloves, goggles and an apron must be worn when checking the electrolyte level. Eye wash solution must be at hand.

Battery Care

82

After topping battery clean battery surface and discard rags

used.

Open the battery covers but

do not open the filler caps

when recharging.

Battery Care

83

  • A simple mnemonic to remember when working with batteries is – WETCAPS



  • Wipe off any dirt or spillages.


  • Electrolyte level 3mm above plates.


  • Tightness of terminals.


  • Cracks in casing.


  • Air holes clear


  • Preservative on terminal


  • Security of battery

Battery Care

Battery care video

84

Battery Care

Thank you for coming

Any Questions

?

85

86

Travel truck first whether laden or unladen

except when positioning the truck to deposit

a load or when travelling on inclines laden.

When laden the load should be positioned

approximately 50mm above the reach legs,

fully reached back with backward tilt applied.

When unladen the forks should be positioned

below the reach legs with backward tilt applied.

Do not use the reach legs to push loads into

position.

Never park the truck with the reach left out.

Additional Rules for Reach Trucks

Thank you for coming

Any Questions

?

87

88

Never use a naked flame when refuelling

or checking fuel levels and Check that there are

no sources of ignition, naked flames, cigarettes etc.

PPE: Always wear suitable gloves when refuelling.

It is advisable to refuel at the end of each shift to reduce

the risk of condensation forming in the fuel tank overnight.

Refuelling Diesel / Petrol Lift Trucks

Take care not to over fill. Wipe away any

spillages and replace filler cap tightly.

Never refuel a truck with the engine running.

Thank you for coming

Any Questions

?

89

90

LPG cylinders should only be changed in the open air or in

well ventilated places.

Check that there are no sources of ignition, naked

flames, cigarettes etc.

Switch off any power tools that may be in the vicinity.

PPE: Eye, hand and foot protection must be worn when

changing LPG cylinders.

Changing Lift Truck L.P.G Cylinders

91

Shut off the hand valve and then unscrew the connector. Check the

connector to ensure the cylinder-sealing washer has lodged in the

connector. Move the connector and hose clear of the cylinder if

necessary tuck it out of the way. Release the strap(s) holding the cylinder to the truck, note the position of the cylinder.

Remove the cylinder and place it in the LPG cylinder storage area.

Keep empty cylinders in a different storage area to the full ones.

Check the new cylinder is the correct type and all fittings are compatible and in good condition.

Place the full cylinder onto the cradle and ensure it is positioned

correctly. (Arrow on bottom of cylinder). Some Cylinders maybe heavy you have to get assistance

Changing Lift Truck L.P.G Cylinders

92

Check the condition of the coupling and hose and make sure the

cylinder-sealing washer is in place. Screw the connector to the

cylinder making sure it is tight. (by hand).

Slowly open the hand valve. The gas will be heard hissing into the

system and it may take a few moments to fill.

In the event of a problem with a cylinder for example gas leaking or the gas not getting through to the system switch off the hand valve before investigating further. Do not drop or roll cylinders along the ground LPG cylinders contain gas under considerable pressure so treat them carefully.

Changing Lift Truck L.P.G Cylinders

Thank you for coming

Any Questions

?

93